Go Back   Land Rover Forum > Land Rover Specific Models > Discovery I
Register Garage All Albums FAQ Community Calendar Today's Posts Search

Discovery I Discuss here about the first version of Land Rover Discovery (Disco I) in this section.


Reply
 
Thread Tools Display Modes
Old 06-19-2016, 07:56 PM   #1
D1driver_mgwarrior
Junior Member
 
Join Date: Jun 2016
Posts: 1
Default Bleeding the cooling system

What is the best way to bleed air from the cooling system?
I have a 98 D1
D1driver_mgwarrior is offline   Reply With Quote
Old 06-19-2016, 08:01 PM   #2
Joey
Senior Member
 
Join Date: Mar 2011
Location: Liberty Twp, OH
Posts: 225
Garage
Default

D1 unlike the D2 is easy to bleed, just fill then run the engine, let cool fill again. Make sure the heater is running.
__________________
This forum is not used much... please go to:

http://www.landroverworld.org


Joey
Cincinnati OH
http://www.customroveraccessories.com Home of the New D2 horn buttons!

http://www.usarovers.com/ (call for Rover parts ask for Nathan 502-222-5859)

Rover Radio issues or IPOD Adapters http://home.valornet.com/splacket/index.htm

EAS fault http://www.rswsolutions.com

When working with GEMS vehicles. Never try to locate a misfire by pulling plug leads off - pull the injector connector instead. Otherwise you can blow up the ECU.

Secondly never swap ECUs between vehicles to test them, because both vehicles and ECUs may stop working, and you'll have to have them all reset by a franchised LR dealer (ouch!).
Joey is offline   Reply With Quote
Old 02-18-2018, 05:36 AM   #3
Grainger
Junior Member
 
Join Date: Jul 2017
Posts: 1
Default

Quote:
Originally Posted by Joey View Post
D1 unlike the D2 is easy to bleed, just fill then run the engine, let cool fill again. Make sure the heater is running.
Hi Joey, what's the best procedure for D2? I don't want to mess anything up.
Grainger is offline   Reply With Quote
Old 02-18-2018, 09:34 AM   #4
Joey
Senior Member
 
Join Date: Mar 2011
Location: Liberty Twp, OH
Posts: 225
Garage
Default

Best way to bleed a D2, park with the front of the rover on a hill or jack it up and place floor stands under the front... as long as the front is 12 inches or so higher than the rear.

Fill overflow tank. Start the engine with heater on warm it up till the t-stat opens (you will know as the overflow tank will probably empty. Shut the engine down, let it cool for 5 minutes or so and repeat until you can't add any more antifreeze.

If you don't have a way to premix antifreeze spend the extra money and buy the 50/50 and always use distilled water if you plan to premix your own.
__________________
This forum is not used much... please go to:

http://www.landroverworld.org


Joey
Cincinnati OH
http://www.customroveraccessories.com Home of the New D2 horn buttons!

http://www.usarovers.com/ (call for Rover parts ask for Nathan 502-222-5859)

Rover Radio issues or IPOD Adapters http://home.valornet.com/splacket/index.htm

EAS fault http://www.rswsolutions.com

When working with GEMS vehicles. Never try to locate a misfire by pulling plug leads off - pull the injector connector instead. Otherwise you can blow up the ECU.

Secondly never swap ECUs between vehicles to test them, because both vehicles and ECUs may stop working, and you'll have to have them all reset by a franchised LR dealer (ouch!).
Joey is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:41 AM.


Sponsor Ads

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.

Garage vBulletin Plugins by Drive Thru Online, Inc.